I had ordered before,
にゃんがーどのねこ工房から返信来ました〜 2018年11月27日
Brace-type door to prevent the cat from jumping out,
Nyan-guard
It arrived several days ago.
Until then, this one,
I used to replace pet guard with cardboard-reinforced one.
I received a notice of completion of creation earlier than I thought
(It was said that it took three months),
To Mr. Seino,
"Because it's a big deal it can not be delivered unless it is daytime on weekdays."
It is said,
It took time to adjust the schedule.
(It is impossible, there is such a work, though ...)
Can you understand in the photograph?
It was tremendously taking a place, really.
Finally we decided to start assembling today.
So, from the conclusion,
The assembly did not end! !
Nyan-guard assembly can not be done alone! ! !
It took me an hour and a half, but
Contents ordered,
Dimension A 2380 B 840 (mm notation)
By the way, my height is 153 cm.
Pretty much like this carpenters? I am in trouble if I am truly living alone.
So it is incomplete but we will inform you about the progress of the assembly.
When opening the package, a lot of wooden sticks were lined up like this.
I will carry it one way or the other.
There were several papers in it.
Greeting message.
Notes.
Attention on the length of the pillars.
It is a booklet of how to make it.
It looks like a lap so it is wrapped.
First of all,
This round bar. It is a part lining up vertically in the door.
The number seems to be different depending on the width.
Then two horizontal frames and a middle frame.
The hole is empty to point to the round bar, but the middle frame is made to penetrate.
The height is different.
Like this.
First I will pass a round bar through the middle frame.
It seems to be about 1/3 from the bottom.
It looks like an accordion.
Fit the horizontal frame, first the bottom part.
Like this?
Next we put a horizontal frame on top, but it is better to lay on a non-slip mat and stand up.
There was also a non-slip mat.
Spread this and this.
Okay, good luck,
Stand against the wall ,,,
As for the work of the high place after all it is necessary to have a stepping stone.
I'd like to put the top horizontal frame ,,,
This was serious! !
Even if it wears, it will come off! ! !
Completion after hardship. .
next,
The keyed frame comes in.
Although the driver comes from here,
This was also packed.
Then,
It is bolt.
Fasten and tighten so as not to forget the washer.
Then, at this time,
Attention to the direction of the keyed frame! !
Key direction and up and down! ! ! !
The direction of the paw of the key pad,
The closer the hole through the side frame is, the lower one.
First of all, tighten the lower locking bolt and the set of round bars with the upper, middle and lower frames with the longer bolt from the outside.
Next up ,,,
The top, it was serious! !
It is slightly misaligned, and moving the outer frame trying to fix it will cause the round bar to come off! !
Somehow fixed. .
Then the middle frame part.
If the middle frame is out of alignment with the hole, move it.
This is the short bolt,
It is the last to be firm, so if you can fix it for the time being OK.
It took at least an hour already at this point.
Next will be pillars at both ends.
Put the legs on the top and bottom of the pillar.
The top is designed to be concave when pushed with spring type.
There is a plate in the bottom, so it seems to be in the adjustment when the height is not enough.
Take it out for the time being.
Prepare two pillars.
The part to attach the door part is connected by a hinge.
Oh ,, this hole ,,,
It becomes the part to attach the middle frame.
This is upside down.
Here, I will remove the pet gate that it tried its best until now.
Remove the brace portion ,,,
It remains a little trace, but, well, this is about being a pardon.
There is no scratch ,,,
It was refreshing.
And I put my legs on the top and bottom of the pillar,
This was also serious! !
Fit it up and fit it down and lift and move,
The bottom goes down! ! !
Somehow it seems to be stabbing, but how about?
Well, I thought that it was completed by installing the door part with bolts,
Here, two unexpected accidents occurred,
In the end I will give up on completion.
First of all,
When you carry it the upper side frame falls off.
When moving with a round bar, only one side is stopped with bolts, so the opposite side will be misaligned. .
In the other,
Actually trying to stop the bolt is not enough! !
I tried to tighten it by bolting the bottom,
If you do not hold down the door part it will fall and fall! !
I could not find something that could hold down the door a bit well,
Eventually, I gave up today on the way. . .
It seems that it is still sweet, as the pillar brace will also shift as you move it.
Sorry. . .
My mother will come next month, so it is left untouched until then.
If there is time and margin, I try again, but
I am already disappointed. . 😩
Mokuren-cha---n, Mama I'm tired
Comfort me ...
"Oh well?"
"No, it can not be helped at all"
Thank you.
original Japanese version →「にゃんがーど」の組み立ては一人じゃ無理でした！！ 2019年1月23日
